10CAG/10CHG/10CGGHz CHANNEL RADIO CONTROL SYSTEM INSTRUCTION MANUAL Technical updates and additional programming examples. Instruction manual • Read online or download PDF • Futaba 10CG GHz User Manual. Futaba 10CHG Pdf User Manuals. View online or download Futaba 10CHG Instruction Manual.
|Published (Last):||4 December 2007|
|PDF File Size:||3.77 Mb|
|ePub File Size:||14.24 Mb|
|Price:||Free* [*Free Regsitration Required]|
Modulation indicator Timers MIX: The T10CG transmitter has been designed to function in many countries. Requires receiver of proper modulation.
FUTABA 10CHG Manuals
For example, the channel 5 servo, which defaults to SWITCH E for retract use, can easily be unassigned NULL to allow for easy use as a second rudder servo in a mix, or to a slider or dial for bomb door or other control. Plug the charger into a wall socket.
The blue LED on the front of the transmitter is turned off. Turn on the receiver.
C Repeat as needed. Different models might require different installations. Instead, gently pull on the the transmitter. Next, unplug the battery wire, and remove the battery from the transmitter. Please set up after pressing Fuatba for 1 second and canceling the alarm display. Due to unforeseen changes in production procedures, the information contained in this manual is subject to change without notice.
Also allows assignment of a channel to mixing only assigned as NULLwith no primary control Switches for which warnings will be issued at power-up are listed below: See Twin elevator servos.
Each transmitter has an individually assigned, unique ID code.
Operating instructions FUTABA 10CHG |
To print the manual completely, please, download it. If so, please follow the model’s instruction manual. GV-1 connections Magnetic sensor Throttle servo Control amp Mixture servo Connected only when fuel 10cg function used. Adjust the servo’s end points. Don’t show me this message again.
Note that this will NOT change the throttle and elevator rachets, etc.
FUTABA 10CAG Instruction Manual
In order to start Chapters Table Of Contents Compensate for pitching up or down when mannual is applied. Other functions you may wish to set up for your model. After two 2 seconds, change to Red. Please be sure to programming, use, set up and safety information on the 10CG radio system and is updated regularly.
Turn off the receiver.
RHS Receiver Futaba’s dual antenna diversity then seamlessly selects the rutaba signal reception between these antennas to ensure that there is no loss of signal. This function selects which of the 15 model memories in the transmitter or ,anual in the optional CAMPacthe model’s name and an image of its type are indicated after its number. Note that if the power switch is turned off prior to completion, the data will not be reset.
The name of the model memory you are copying into is displayed for clarity. When the warning does not stop even when the mixing switch indicated by the warning display on the screen is turned off, the functions mxnual previously probably use the same switch and the OFF direction setting is reversed.
Got it, continue to print.
Transmitter charging indicator RX: When the length feels comfortable, lock the position by turning locking piece B counterclockwise. To reset the timer, press Dial for one second. Also includes Battery FailSafe settings By giving each model a name that is immediately recognizable, a crash. Swashplate function rate settings SWASH AFR travel of the aileron, elevator except H-2 and collective pitch functions, adjusting or reversing the motion of all servos involved in that function, only when using that function.
Comments to this Manuals Your Name.
The features that are identical refer back to the ACRO chapter. Coaxial cable Antenna from the standard Futaba receiver. Do not over tighten the screws. In order to start operation, the receiver must be linked with the ID code of the transmitter with which it is being paired.
Futaba 10CAG Instruction Manual – Page 1 of |
Area Selection Frequency Range: It is not intended Avoid plugging multiple extensions together to attain your desired length. If there are some FASST futzba turned on near the receiver, the LED may show the above status for a brief moment before changing to the status indication as shown in the “LED indication” table above.
Larger models can have large metal objects that can attenuate the RF signal.
For details on setting up a complex aerobatic plane, please visit www.