Menu

ELIWELL ID970 PDF

0 Comment

Buy Eliwell On/Off Temperature Controller, 74 x 32mm, NTC, PTC Input, 12 V ac/ dc Supply ID Browse our latest on-off-temperature-controllers offers. Buy Eliwell On/Off Temperature Controller, 74 x 32mm, PTC Input, V ac Supply, → +°C Measurement Range ID V 8A+PTC. Browse our. In order to configure the instrument for this purpose you must access the folder identified by the “Add” label and use the parameters “dEA” and “FAA”. ID LX.

Author: Arashikree Vulkis
Country: Brunei Darussalam
Language: English (Spanish)
Genre: Politics
Published (Last): 27 December 2016
Pages: 393
PDF File Size: 2.95 Mb
ePub File Size: 1.6 Mb
ISBN: 422-6-75432-701-7
Downloads: 56197
Price: Free* [*Free Regsitration Required]
Uploader: Salmaran

The sensor has no connection polarity and can be extended using an ordinary bipolar cable note that extending the probe may affect the electromagnetic compatibility EMC of the instrument: In id97 conditions, the labels for the Set point value is found in the menu. Any protection devices required to comply with product requirements or dictated by common sense due to obvious safety reasons should be installed externally.

Single stage controller for temperature ID The two sets are interdependent: Temperature value understood as distance from the Setpoint or as an absolute value based on Att which if exceeded in a downward direction triggers the activation of the alarm signal.

Eliwell ID MC (Milk) |

The operation cannot be cancelled. For higher loads, use a suitable contactor. Description Technical Schema Description: This means, for example, that an error introduced by the probe is added to any error that is typical of the instrument. The programming parameters are downloaded when the device is switched on.

TOP Related  YN-622C MANUAL DOWNLOAD

HSE maximum set cannot be less than LSE minimum set and vice versa Compressor activation time in the event of a faulty probe.

Although Eliwell has taken all possible measures to guarantee the accuracy of this document, it declines any responsibility for any damage arising out of its use. The parameter indicates that the protection is active on compressor relay actuations. It is still possible to enter parameter programming and modify the parameters, including the status of this parameter, in order to allow keyboard unlocking.

Eliwell ID970 MC (Milk)

Compressor off time in the event of a faulty probe. TTL for connection to Copy Card 3 outputs on relays: View with decimal point.

ID Single stage controller for temperature.

JavaScript is disabled in your browser. There are 2 operating modes determined by parameter AtP: Set point setting folder; -Pb1: Programming parameter transfer from Copy Card to instrument. Temperature alarm signal delay time.

The device must be suitably protected from water and dust according to the specific application and only be accessible using special tools except for the front keypad. In addition, the 16 A compressor relay options and the buzzer are provided. It is classified as follows: At least the indicated time must elapse between switch-off of the compressor relay rliwell the successive switch-on.

TOP Related  GUARDIANS OF BEING ECKHART TOLLE PDF

The instrument has eliwrll terminals for connecting electrical cables with a maximum diameter of 2.

Download from reset Connect the copy card when the instrument is OFF. Make sure that the power voltage complies with the device voltage. Single stage controller for temperature – ID The ID controllers are devices suitable for applications on normal or low temperature refrigerating units.

ID A Single stage controller for temperature. Erasing all parameters in the key. Programming parameter transfer from instrument to Copy Card.

Minimum possible setpoint value. Alarm exclusion time after instrument is switched on following a power failure. The parameter indicates that a protection is active on the relay actuations of the generic compressor. The Setpoint ie970 also be viewed.

ID LX Single stage controller for temperature. Single stage controller for temperature. Defrost counting is always active when the machine is on and starts at each power-on. Maximum possible setpoint value. Temperature value understood as distance from the Setpoint or as an absolute value based on Att which if exceeded in an upward direction triggers the activation of id70 alarm signal.

The password is enabled if the value of the PA1 parameter is not 0.