ASTM D is a test method used to study the apparent tensile strength of plastic pipes using a specialized test fixture. The ASTM D standard determines the comparative apparent tensile strength of most plastic products using a split disk test fixture tested under defined. ASTM D TESTING FIXTURE. Split disk and ring segment tensile tests, properly interpreted, provide reasonably accurate information with regard to.
|Published (Last):||24 December 2005|
|PDF File Size:||2.85 Mb|
|ePub File Size:||9.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
This potential error astm d2290 analyzed and discussed in detail in References 2 and 3. The version of ASTM Adtm has added a Procedure D, for testing astm d2290 pipe with a nominal diameter of 14″ and greater and preferably having a astm d2290 thickness 1″ and greater.
Wyoming Test Fixtures Inc. Extruded and molded thermoplastic piping is also covered by this test. Rather than testing a complete ring, two 4″ long segments of the ring are tested together in a special fixture fully defined in ASTM D Astm d2290 original fixture for testing Procedure A specimens, i.
Give one of our application engineers a d2290 today for help with creating astm d2290 best budget and testing plan according to ASTM D This test method d2209 applicable to reinforced-thermosetting resin pipe regardless of fabrication method.
Link to Active This link will always route to the current Active version of the standard.
ASTM D TESTING FIXTURE
In general, this test method is still generally considered an acceptable test for unidirectional hoop-wound composite rings. The ASTM D standard determines the comparative apparent tensile strength of most plastic products using a split disk test fixture tested under defined conditions and test machine speed. However, this now deleted original Procedure A fixture, while dd2290 longer astm d2290 ASTM standard, is still used for testing filament-wound composite rings, and the fixture is available from Wyoming Test Fixtures, Inc.
Historical Version s – view previous versions of standard. The astm d2290 Procedure B and C specimens, extruded and molded unreinforced plastic specimens and larger diameter astm d2290 plastic pipe, respectively, utilized fixtures of the general astm d2290 shown at the right side of Fig. Procedure C has been used on polyethylene and polybutylene pipe to produce results astm d2290 to Quick Burst results Test Method D for 4 in.
ASTM D2290 TESTING FIXTURE
These effects are discussed in References 3 and 4. Procedure A is now used for testing reinforced-thermosetting resin pipe, Procedure B for thermoplastic pipe of any size, and Procedure Astm d2290 for thermoplastic pipe with astm d2290 diameters of 4. The test cannot be considered significant for applications differing widely from the load-time atsm of the standard test.
One criticism is that some bending is induced in the ring specimen at the split. This test method also is applicable to extruded and molded thermoplastic pipe. Details of the now obsolete fixture and specimen for testing filament-wound rings can be found can be found in and earlier versions of ASTM D Astm d2290 Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
By means of our plastic testing expertise astm d2290 modular product design, we will help find the testing solution that is right astm d2290 you.
ASTM D Plastic or Reinforced Plastic Pipe Tensile Testing Equipment
Have a question about conducting the test for this standard? These various specimen configurations and test procedures are fully defined in the astm d2290 of Astm d2290 D Reference 1. Procedure D is used for polyethylene pipe with a nominal diameter of 14 in. The values given in parentheses are mathematical conversions to SI units that are provided for v2290 only and are not considered standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to astm d2290.
Within limits, specimens of varying sizes can be tested using the same holders, by using interchangeable pairs of split disks. We are confident that we have astm d2290 you are looking for.
Data from this test are useful for research and development, quality control specification and design. These former Procedure A specimens are astm d2290 rings of controlled diameter, width, and thickness, astm d2290. Procedure E is used for polyvinyl chloride PVC pipe with a nominal diameter of 14 in.
ASTM D2290 Plastic or Reinforced Plastic Pipe Tensile Testing Equipment
Friction between the split disk fixture and the ring specimen is also a astm d2290. Force range of 5 kN to kN 1, lbf to astm d2290, lbf Adjustable test space The most popular choice for static tension and compression tests These dual 2d290 testers are available in both tabletop and floor standing models.
Work Item s – proposed revisions of this aatm. Reinforced thermosetting resin pipe may be tested by this astm d2290 regardless of fabrication method. Although this original Procedure A test method was an ASTM standard from toits popularity has varied over the years. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications.
Sources of Additional Astm d2290 All of these revised procedures use the same general fixture configuration the configuration shown on the right side astm d2290 Fig.